- Jun 30, 2020
-
-
Fabian Vogt authored
[ Upstream commit 7dfc06a0 ] It is possible that the first event in the event log is not actually a log header at all, but rather a normal event. This leads to the cast in __calc_tpm2_event_size being an invalid conversion, which means that the values read are effectively garbage. Depending on the first event's contents, this leads either to apparently normal behaviour, a crash or a freeze. While this behaviour of the firmware is not in accordance with the TCG Client EFI Specification, this happens on a Dell Precision 5510 with the TPM enabled but hidden from the OS ("TPM On" disabled, state otherwise untouched). The EFI firmware claims that the TPM is present and active and that it supports the TCG 2.0 event log format. Fortunately, this can be worked around by simply checking the header of the first event and the event log header signature itself. Commit b4f1874c ("tpm: check event log version before reading final events") addressed a similar issue also found on Dell models. Fixes: 6b032619 ("efi: Attempt to get the TCG2 event log in the boot stub") Signed-off-by:
Fabian Vogt <fvogt@suse.de> Link: https://lore.kernel.org/r/1927248.evlx2EsYKh@linux-e202.suse.de Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1165773 Signed-off-by:
Ard Biesheuvel <ardb@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Srinivas Kandagatla authored
[ Upstream commit 6476b60f ] Successful send of EOS command does not indicate that EOS is actually finished, correct event to wait EOS is finished is EOS_RENDERED event. EOS_RENDERED means that the DSP has finished processing all the buffers for that particular session and stream. This patch fixes EOS handling! Fixes: 68fd8480 ("ASoC: qdsp6: q6asm: Add support to audio stream apis") Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20200611124159.20742-3-srinivas.kandagatla@linaro.org Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Huy Nguyen authored
[ Upstream commit 94579ac3 ] During IPsec performance testing, we see bad ICMP checksum. The error packet has duplicated ESP trailer due to double validate_xmit_xfrm calls. The first call is from ip_output, but the packet cannot be sent because netif_xmit_frozen_or_stopped is true and the packet gets dev_requeue_skb. The second call is from NET_TX softirq. However after the first call, the packet already has the ESP trailer. Fix by marking the skb with XFRM_XMIT bit after the packet is handled by validate_xmit_xfrm to avoid duplicate ESP trailer insertion. Fixes: f6e27114 ("net: Add a xfrm validate function to validate_xmit_skb") Signed-off-by:
Huy Nguyen <huyn@mellanox.com> Reviewed-by:
Boris Pismenny <borisp@mellanox.com> Reviewed-by:
Raed Salem <raeds@mellanox.com> Reviewed-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 77cad9db ] We must check for "dss_core" instead of "dss" to avoid also matching also "dss_dispc". This only matters for the mixed case of data configured in device tree but with legacy booting ti,hwmods property still enabled. Fixes: 8b30919a ("ARM: OMAP2+: Handle reset quirks for dynamically allocated modules") Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 08b91dd6 ] We must ignore the clockactivity bit for most modules and not set it unless specified for the module with SYSC_QUIRK_USE_CLOCKACT. Otherwise the interface clock can be automatically gated constantly causing unexpected performance issues. Fixes: ae9ae12e ("bus: ti-sysc: Handle clockactivity for enable and disable") Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 5ce8aee8 ] Looks like we're missing flush of posted write after module enable and disable. I've seen occasional errors accessing various modules, and it is suspected that the lack of posted writes can also cause random reboots. The errors we can see are similar to the one below from spi for example: 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read): Data Access in User mode during Functional access ... mcspi_wait_for_reg_bit omap2_mcspi_transfer_one spi_transfer_one_message ... We also want to also flush posted write for disable. The clkctrl clock disable happens after module disable, and we don't want to have the module potentially stay active while we're trying to disable the clock. Fixes: d59b6056 ("bus: ti-sysc: Add generic enable/disable functions") Signed-off-by:
-
Dennis Dalessandro authored
commit 822fbd37 upstream. When the try_module_get calls were removed from opening and closing of the i2c debugfs file, the corresponding module_put calls were missed. This results in an inaccurate module use count that requires a power cycle to fix. Fixes: 09fbca8e ("IB/hfi1: No need to use try_module_get for debugfs") Link: https://lore.kernel.org/r/20200623203230.106975.76240.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by:
Kaike Wan <kaike.wan@intel.com> Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Jason Gunthorpe <jgg@nvidia.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shay Drory authored
commit 116a1b9f upstream. Currently, when RMPP MADs are processed while the MAD agent is destroyed, it could result in use after free of rmpp_recv, as decribed below: cpu-0 cpu-1 ----- ----- ib_mad_recv_done() ib_mad_complete_recv() ib_process_rmpp_recv_wc() unregister_mad_agent() ib_cancel_rmpp_recvs() cancel_delayed_work() process_rmpp_data() start_rmpp() queue_delayed_work(rmpp_recv->cleanup_work) destroy_rmpp_recv() free_rmpp_recv() cleanup_work()[1] spin_lock_irqsave(&rmpp_recv->agent->lock) <-- use after free [1] cleanup_work() == recv_cleanup_handler Fix it by waiting for the MAD agent reference count becoming zero before calling to ib_cancel_rmpp_recvs(). Fixes: 9a41e38a ("IB/mad: Use IDR for agent IDs") Link: https://lore.kernel.org/r/20200621104738.54850-2-leon@kernel.org Signed-off-by:
Shay Drory <shayd@mellanox.com> Reviewed-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
Zheng Bin authored
commit f4bd34b1 upstream. When a filesystem is mounted on a loop device and on a loop ioctl LOOP_SET_STATUS64, because of kill_bdev, buffer_head mappings are getting destroyed. kill_bdev truncate_inode_pages truncate_inode_pages_range do_invalidatepage block_invalidatepage discard_buffer -->clear BH_Mapped flag sb_bread __bread_gfp bh = __getblk_gfp -->discard_buffer clear BH_Mapped flag __bread_slow submit_bh submit_bh_wbc BUG_ON(!buffer_mapped(bh)) --> hit this BUG_ON Fixes: 5db470e2 ("loop: drop caches if offset or block_size are changed") Signed-off-by:
Zheng Bin <zhengbin13@huawei.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Joakim Tjernlund authored
commit 03894573 upstream. USB_DEVICE(0x0424, 0x274e) can send data before cdc_acm is ready, causing garbage chars on the TTY causing stray input to the shell and/or login prompt. Signed-off-by:
Joakim Tjernlund <joakim.tjernlund@infinera.com> Cc: stable@vger.kernel.org Acked-by:
Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20200605105418.22263-1-joakim.tjernlund@infinera.com Signed-off-by:
-
Kai-Heng Feng authored
commit f0c472a6 upstream. Just return if xHCI is quirked to disable LPM. We can save some time from reading registers and doing spinlocks. Add stable tag as we want this patch together with the next one, "Poll for U0 after disabling USB2 LPM" which fixes a suspend issue for some USB2 LPM devices Cc: stable@vger.kernel.org Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200624135949.22611-5-mathias.nyman@linux.intel.com Signed-off-by:
-
Al Cooper authored
commit a73d9d9c upstream. Unable to complete the enumeration of a USB TV Tuner device. Per XHCI spec (4.6.5), the EP state field of the input context shall be cleared for a set address command. In the special case of an FS device that has "MaxPacketSize0 = 8", the Linux XHCI driver does not do this before evaluating the context. With an XHCI controller that checks the EP state field for parameter context error this causes a problem in cases such as the device getting reset again after enumeration. When that field is cleared, the problem does not occur. This was found and fixed by Sasi Kumar. Cc: stable@vger.kernel.org Signed-off-by:
Al Cooper <alcooperx@gmail.com> Signed-off-by:
-
Mathias Nyman authored
commit dceea670 upstream. EP_STATE_MASK should be 0x7 instead of 0xf xhci spec 6.2.3 shows that the EP state field in the endpoint context data structure consist of bits [2:0]. The old value included a bit from the next field which fortunately is a RsvdZ region. So hopefully this hasn't caused too much harm Cc: stable@vger.kernel.org Signed-off-by:
-
Zhang Xiaoxu authored
commit 6b690402 upstream. CIFS implements the fallocate(FALLOC_FL_ZERO_RANGE) with send SMB ioctl(FSCTL_SET_ZERO_DATA) to server. It just set the range of the remote file to zero, but local page cache not update, then the data inconsistent with server, which leads the xfstest generic/008 failed. So we need to remove the local page caches before send SMB ioctl(FSCTL_SET_ZERO_DATA) to server. After next read, it will re-cache it. Fixes: 30175628 ("[SMB3] Enable fallocate -z support for SMB3 mounts") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Zhang Xiaoxu <zhangxiaoxu5@huawei.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Cc: stable@vger.kernel.org # v3.17 Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Zhang Xiaoxu authored
commit acc91c2d upstream. When punch hole success, we also can read old data from file: # strace -e trace=pread64,fallocate xfs_io -f -c "pread 20 40" \ -c "fpunch 20 40" -c"pread 20 40" file pread64(3, " version 5.8.0-rc1+"..., 40, 20) = 40 fallocate(3, FALLOC_FL_KEEP_SIZE|FALLOC_FL_PUNCH_HOLE, 20, 40) = 0 pread64(3, " version 5.8.0-rc1+"..., 40, 20) = 40 CIFS implements the fallocate(FALLOCATE_FL_PUNCH_HOLE) with send SMB ioctl(FSCTL_SET_ZERO_DATA) to server. It just set the range of the remote file to zero, but local page caches not updated, then the local page caches inconsistent with server. Also can be found by xfstests generic/316. So, we need to remove the page caches before send the SMB ioctl(FSCTL_SET_ZERO_DATA) to server. Fixes: 31742c5a ("enable fallocate punch hole ("fallocate -p") for SMB3") Suggested-by:
-
Xiyu Yang authored
commit 77577de6 upstream. open_shroot() invokes kref_get(), which increases the refcount of the "tcon->crfid" object. When open_shroot() returns not zero, it means the open operation failed and close_shroot() will not be called to decrement the refcount of the "tcon->crfid". The reference counting issue happens in one normal path of open_shroot(). When the cached root have been opened successfully in a concurrent process, the function increases the refcount and jump to "oshr_free" to return. However the current return value "rc" may not equal to 0, thus the increased refcount will not be balanced outside the function, causing a refcnt leak. Fix this issue by setting the value of "rc" to 0 before jumping to "oshr_free" label. Signed-off-by:
Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by:
Xin Tan <tanxin.ctf@gmail.com> Signed-off-by:
-
Steffen Maier authored
commit 936e6b85 upstream. Suppose that, for unrelated reasons, FSF requests on behalf of recovery are very slow and can run into the ERP timeout. In the case at hand, we did adapter recovery to a large degree. However due to the slowness a LUN open is pending so the corresponding fc_rport remains blocked. After fast_io_fail_tmo we trigger close physical port recovery for the port under which the LUN should have been opened. The new higher order port recovery dismisses the pending LUN open ERP action and dismisses the pending LUN open FSF request. Such dismissal decouples the ERP action from the pending corresponding FSF request by setting zfcp_fsf_req->erp_action to NULL (among other things) [zfcp_erp_strategy_check_fsfreq()]. If now the ERP timeout for the pending open LUN request runs out, we must not use zfcp_fsf_req->erp_action in the ERP timeout handler. This is a problem since v4.15 commit 75492a51 ("s390/scsi: Convert timers to use timer_setup()"). Before that we intentionally only passed zfcp_erp_action as context argument to zfcp_erp_timeout_handler(). Note: The lifetime of the corresponding zfcp_fsf_req object continues until a (late) response or an (unrelated) adapter recovery. Just like the regular response path ignores dismissed requests [zfcp_fsf_req_complete() => zfcp_fsf_protstatus_eval() => return early] the ERP timeout handler now needs to ignore dismissed requests. So simply return early in the ERP timeout handler if the FSF request is marked as dismissed in its status flags. To protect against the race where zfcp_erp_strategy_check_fsfreq() dismisses and sets zfcp_fsf_req->erp_action to NULL after our previous status flag check, return early if zfcp_fsf_req->erp_action is NULL. After all, the former ERP action does not need to be woken up as that was already done as part of the dismissal above [zfcp_erp_action_dismiss()]. This fixes the following panic due to kernel page fault in IRQ context: Unable to handle kernel pointer dereference in virtual kernel address space Failing address: 0000000000000000 TEID: 0000000000000483 Fault in home space mode while using kernel ASCE. AS:000009859238c00b R2:00000e3e7ffd000b R3:00000e3e7ffcc007 S:00000e3e7ffd7000 P:000000000000013d Oops: 0004 ilc:2 [#1] SMP Modules linked in: ... CPU: 82 PID: 311273 Comm: stress Kdump: loaded Tainted: G E X ... Hardware name: IBM 8561 T01 701 (LPAR) Krnl PSW : 0404c00180000000 001fffff80549be0 (zfcp_erp_notify+0x40/0xc0 [zfcp]) R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3 Krnl GPRS: 0000000000000080 00000e3d00000000 00000000000000f0 0000000000030000 000000010028e700 000000000400a39c 000000010028e700 00000e3e7cf87e02 0000000010000000 0700098591cb67f0 0000000000000000 0000000000000000 0000033840e9a000 0000000000000000 001fffe008d6bc18 001fffe008d6bbc8 Krnl Code: 001fffff80549bd4: a7180000 lhi %r1,0 001fffff80549bd8: 4120a0f0 la %r2,240(%r10) #001fffff80549bdc: a53e0003 llilh %r3,3 >001fffff80549be0: ba132000 cs %r1,%r3,0(%r2) 001fffff80549be4: a7740037 brc 7,1fffff80549c52 001fffff80549be8: e320b0180004 lg %r2,24(%r11) 001fffff80549bee: e31020e00004 lg %r1,224(%r2) 001fffff80549bf4: 412020e0 la %r2,224(%r2) Call Trace: [<001fffff80549be0>] zfcp_erp_notify+0x40/0xc0 [zfcp] [<00000985915e26f0>] call_timer_fn+0x38/0x190 [<00000985915e2944>] expire_timers+0xfc/0x190 [<00000985915e2ac4>] run_timer_softirq+0xec/0x218 [<0000098591ca7c4c>] __do_softirq+0x144/0x398 [<00000985915110aa>] do_softirq_own_stack+0x72/0x88 [<0000098591551b58>] irq_exit+0xb0/0xb8 [<0000098591510c6a>] do_IRQ+0x82/0xb0 [<0000098591ca7140>] ext_int_handler+0x128/0x12c [<0000098591722d98>] clear_subpage.constprop.13+0x38/0x60 ([<000009859172ae4c>] clear_huge_page+0xec/0x250) [<000009859177e7a2>] do_huge_pmd_anonymous_page+0x32a/0x768 [<000009859172a712>] __handle_mm_fault+0x88a/0x900 [<000009859172a860>] handle_mm_fault+0xd8/0x1b0 [<0000098591529ef6>] do_dat_exception+0x136/0x3e8 [<0000098591ca6d34>] pgm_check_handler+0x1c8/0x220 Last Breaking-Event-Address: [<001fffff80549c88>] zfcp_erp_timeout_handler+0x10/0x18 [zfcp] Kernel panic - not syncing: Fatal exception in interrupt Link: https://lore.kernel.org/r/20200623140242.98864-1-maier@linux.ibm.com Fixes: 75492a51 ("s390/scsi: Convert timers to use timer_setup()") Cc: <stable@vger.kernel.org> #4.15+ Reviewed-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
Steffen Maier <maier@linux.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Roman Bolshakov authored
commit 632f24f0 upstream. The driver performs SCR (state change registration) in all modes including pure target mode. For each RSCN, scan_needed flag is set in qla2x00_handle_rscn() for the port mentioned in the RSCN and fabric rescan is scheduled. During the rescan, GNN_FT handler, qla24xx_async_gnnft_done() deletes session of the port that caused the RSCN. In target mode, the session deletion has an impact on ATIO handler, qlt_24xx_atio_pkt(). Target responds with SAM STATUS BUSY to I/O incoming from the deleted session. qlt_handle_cmd_for_atio() and qlt_handle_task_mgmt() return -EFAULT if they are not able to find session of the command/TMF, and that results in invocation of qlt_send_busy(): qlt_24xx_atio_pkt_all_vps: qla_target(0): type 6 ox_id 0014 qla_target(0): Unable to send command to target, sending BUSY status Such response causes command timeout on the initiator. Error handler thread on the initiator will be spawned to abort the commands: scsi 23:0:0:0: tag#0 abort scheduled scsi 23:0:0:0: tag#0 aborting command qla2xxx [0000:af:00.0]-188c:23: Entered qla24xx_abort_command. qla2xxx [0000:af:00.0]-801c:23: Abort command issued nexus=23:0:0 -- 0 2003. Command abort is rejected by target and fails (2003), error handler then tries to perform DEVICE RESET and TARGET RESET but they're also doomed to fail because TMFs are ignored for the deleted sessions. Then initiator makes BUS RESET that resets the link via qla2x00_full_login_lip(). BUS RESET succeeds and brings initiator port up, SAN switch detects that and sends RSCN to the target port and it fails again the same way as described above. It never goes out of the loop. The change breaks the RSCN loop by keeping initiator sessions mentioned in RSCN payload in all modes, including dual and pure target mode. Link: https://lore.kernel.org/r/20200605144435.27023-1-r.bolshakov@yadro.com Fixes: 2037ce49 ("scsi: qla2xxx: Fix stale session") Cc: Quinn Tran <qutran@marvell.com> Cc: Arun Easi <aeasi@marvell.com> Cc: Nilesh Javali <njavali@marvell.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Daniel Wagner <dwagner@suse.de> Cc: Himanshu Madhani <himanshu.madhani@oracle.com> Cc: Martin Wilck <mwilck@suse.com> Cc: stable@vger.kernel.org # v5.4+ Reviewed-by:
Daniel Wagner <dwagner@suse.de> Reviewed-by:
Shyam Sundar <ssundar@marvell.com> Reviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by:
-
Peter Chen authored
commit 2587a029 upstream. The other thread may access other endpoints when the cdns3_check_new_setup is handling, add spinlock to protect it. Cc: <stable@vger.kernel.org> Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver") Reviewed-by:
Pawel Laszczak <pawell@cadence.com> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org> Signed-off-by:
-
Peter Chen authored
commit b51e1cf6 upstream. The 'tmode' is ctrl->wIndex, changing it as the real test mode value for register assignment. Cc: <stable@vger.kernel.org> Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver") Reviewed-by:
Jun Li <jun.li@nxp.com> Signed-off-by:
-
Peter Chen authored
commit ba3a80fe upstream. It should use the correct direction value from register, not depends on previous software setting. It fixed the EP number wrong issue at trace when the TRBERR interrupt occurs for EP0IN. When the EP0IN IOC has finished, software prepares the setup packet request, the expected direction is OUT, but at that time, the TRBERR for EP0IN may occur since it is DMULT mode, the DMA does not stop until TRBERR has met. Cc: <stable@vger.kernel.org> Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver") Reviewed-by:
-
Takashi Iwai authored
commit 220345e9 upstream. The USB-audio mixer code holds a linked list of usb_mixer_elem_list, and several operations are performed for each mixer element. A few of them (snd_usb_mixer_notify_id() and snd_usb_mixer_interrupt_v2()) assume each mixer element being a usb_mixer_elem_info object that is a subclass of usb_mixer_elem_list, cast via container_of() and access it members. This may result in an out-of-bound access when a non-standard list element has been added, as spotted by syzkaller recently. This patch adds a new field, is_std_info, in usb_mixer_elem_list to indicate that the element is the usb_mixer_elem_info type or not, and skip the access to such an element if needed. Reported-by:
<syzbot+fb14314433463ad51625@syzkaller.appspotmail.com> Reported-by:
<syzbot+2405ca3401e943c538b5@syzkaller.appspotmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200624122340.9615-1-tiwai@suse.de Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Macpaul Lin authored
commit a32a1fc9 upstream. We've found Samsung USBC Headset (AKG) (VID: 0x04e8, PID: 0xa051) need a tiny delay after each class compliant request. Otherwise the device might not be able to be recognized each times. Signed-off-by:
Chihhao Chen <chihhao.chen@mediatek.com> Signed-off-by:
Macpaul Lin <macpaul.lin@mediatek.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1592910203-24035-1-git-send-email-macpaul.lin@mediatek.com Signed-off-by:
-
Yick W. Tse authored
commit c9808bbf upstream. fix error "clock source 41 is not valid, cannot use" [] New USB device found, idVendor=154e, idProduct=1002, bcdDevice= 1.00 [] New USB device strings: Mfr=1, Product=2, SerialNumber=0 [] Product: DCD-1500RE [] Manufacturer: D & M Holdings Inc. [] [] clock source 41 is not valid, cannot use [] usbcore: registered new interface driver snd-usb-audio Signed-off-by:
Yick W. Tse <y_w_tse@yahoo.com.hk> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1373857985.210365.1592048406997@mail.yahoo.com Signed-off-by:
-
Laurence Tratt authored
commit e7585db1 upstream. This uses the same quirk as the Motu M2 and M4 to ensure the driver uses the audio interface's clock. Tested on an SSL2+. Signed-off-by:
Laurence Tratt <laurie@tratt.net> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200612111807.dgnig6rwhmsl2bod@overdrive.tratt.net Signed-off-by:
-
Li Jun authored
commit 302c570b upstream. John reported screaming irq caused by rt1711h when system boot[1], this is because irq request is done before tcpci_register_port(), so the chip->tcpci has not been setup, irq handler is entered but can't do anything, this patch is to address this by moving the irq request after tcpci_register_port(). [1] https://lore.kernel.org/linux-usb/20200530040157.31038-1-john.stultz@linaro.org Fixes: ce08eaeb ("staging: typec: rt1711h typec chip driver") Cc: stable <stable@vger.kernel.org> # v4.18+ Cc: John Stultz <john.stultz@linaro.org> Reported-and-tested-by:
John Stultz <john.stultz@linaro.org> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
-
Tang Bin authored
commit 44ed240d upstream. If the function platform_get_irq() failed, the negative value returned will not be detected here. So fix error handling in exynos_ehci_probe(). And when get irq failed, the function platform_get_irq() logs an error message, so remove redundant message here. Fixes: 1bcc5aa8 ("USB: Add initial S5P EHCI driver") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by:
Tang Bin <tangbin@cmss.chinamobile.com> Link: https://lore.kernel.org/r/20200602114708.28620-1-tangbin@cmss.chinamobile.com Signed-off-by:
-
Kai-Heng Feng authored
commit b3d71abd upstream. USB2 devices with LPM enabled may interrupt the system suspend: [ 932.510475] usb 1-7: usb suspend, wakeup 0 [ 932.510549] hub 1-0:1.0: hub_suspend [ 932.510581] usb usb1: bus suspend, wakeup 0 [ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended [ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended .. [ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03 .. [ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16 [ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16 [ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16 During system suspend, USB core will let HC suspends the device if it doesn't have remote wakeup enabled and doesn't have any children. However, from the log above we can see that the usb 1-7 doesn't get bus suspended due to not in U0. After a while the port finished U2 -> U0 transition, interrupts the suspend process. The observation is that after disabling LPM, port doesn't transit to U0 immediately and can linger in U2. xHCI spec 4.23.5.2 states that the maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for the affected device is advertised as 400us, which is still not enough based on my testing result. So let's use the maximum permitted latency, 10000, to poll for U0 status to solve the issue. Cc: stable@vger.kernel.org Signed-off-by:
-
Macpaul Lin authored
commit a24d5072 upstream. When runtime suspend was enabled, runtime suspend might happen when xhci is removing hcd. This might cause kernel panic when hcd has been freed but runtime pm suspend related handle need to reference it. Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Longfang Liu authored
commit 1ddcb71a upstream. A Synopsys USB2.0 core used in Huawei Kunpeng920 SoC has a bug which might cause the host controller not issuing ping. Bug description: After indicating an Interrupt on Async Advance, the software uses the doorbell mechanism to delete the Next Link queue head of the last executed queue head. At this time, the host controller still references the removed queue head(the queue head is NULL). NULL reference causes the host controller to lose the USB device. Solution: After deleting the Next Link queue head, when has_synopsys_hc_bug set to 1，the software can write one of the valid queue head addresses to the ASYNCLISTADDR register to allow the host controller to get the valid queue head. in order to solve that problem, this patch set the flag for Huawei Kunpeng920 There are detailed instructions and solutions in this patch: commit 2f7ac6c1 ("USB: ehci: add workaround for Synopsys HC bug") Signed-off-by:
Longfang Liu <liulongfang@huawei.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/1591588019-44284-1-git-send-email-liulongfang@huawei.com Signed-off-by:
-
Tomasz Meresiński authored
commit 5d802192 upstream. The Logitech C922, just like other Logitech webcams, needs the USB_QUIRK_DELAY_INIT or it will randomly not respond after device connection Signed-off-by:
Tomasz Meresiński <tomasz@meresinski.eu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200603203347.7792-1-tomasz@meresinski.eu Signed-off-by:
-
Minas Harutyunyan authored
commit 207324a3 upstream. During dwc2 driver probe, after gadget registration to the udc class driver, if exist any builtin function driver it immediately bound to dwc2 and after init host side (dwc2_hcd_init()) stucked in host mode. Patch postpone gadget registration after host side initialization done. Fixes: 117777b2 ("usb: dwc2: Move gadget probe function into platform code") Reported-by:
kbuild test robot <lkp@intel.com> Tested-by:
Marek Vasut <marex@denx.de> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Minas Harutyunyan <hminas@synopsys.com> Link: https://lore.kernel.org/r/f21cb38fecc72a230b86155d94c7e60c9cb66f58.1591690938.git.hminas@synopsys.com Signed-off-by:
-
Chuhong Yuan authored
commit 07c112fb upstream. This driver misses calling iounmap() in remove to undo the ioremap() called in probe. Add the missed call to fix it. Fixes: f54aab6e ("usb: ohci-sm501 driver") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Acked-by:
-
Todd Kjos authored
commit d35d3660 upstream. The binder driver makes the assumption proc->context pointer is invariant after initialization (as documented in the kerneldoc header for struct proc). However, in commit f0fe2c0f ("binder: prevent UAF for binderfs devices II") proc->context is set to NULL during binder_deferred_release(). Another proc was in the middle of setting up a transaction to the dying process and crashed on a NULL pointer deref on "context" which is a local set to &proc->context: new_ref->data.desc = (node == context->binder_context_mgr_node) ? 0 : 1; Here's the stack: [ 5237.855435] Call trace: [ 5237.855441] binder_get_ref_for_node_olocked+0x100/0x2ec [ 5237.855446] binder_inc_ref_for_node+0x140/0x280 [ 5237.855451] binder_translate_binder+0x1d0/0x388 [ 5237.855456] binder_transaction+0x2228/0x3730 [ 5237.855461] binder_thread_write+0x640/0x25bc [ 5237.855466] binder_ioctl_write_read+0xb0/0x464 [ 5237.855471] binder_ioctl+0x30c/0x96c [ 5237.855477] do_vfs_ioctl+0x3e0/0x700 [ 5237.855482] __arm64_sys_ioctl+0x78/0xa4 [ 5237.855488] el0_svc_common+0xb4/0x194 [ 5237.855493] el0_svc_handler+0x74/0x98 [ 5237.855497] el0_svc+0x8/0xc The fix is to move the kfree of the binder_device to binder_free_proc() so the binder_device is freed when we know there are no references remaining on the binder_proc. Fixes: f0fe2c0f ("binder: prevent UAF for binderfs devices II") Acked-by:
Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by:
Todd Kjos <tkjos@google.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200622200715.114382-1-tkjos@google.com Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit ff58bbc7 ] With the recent full-duplex support of implicit feedback streams, an endpoint can be still running after closing the capture stream as long as the playback stream with the sync-endpoint is running. In such a state, the URBs are still be handled and they may call retire_data_urb callback, which tries to transfer the data from the PCM buffer. Since the PCM stream gets closed, this may lead to use-after-free. This patch adds the proper clearance of the callback at stopping the capture stream for addressing the possible UAF above. Fixes: 10ce77e4 ("ALSA: usb-audio: Add duplex sound support for USB devices using implicit feedback") Link: https://lore.kernel.org/r/20200616120921.12249-1-tiwai@suse.de Signed-off-by:
-
Al Viro authored
[ Upstream commit 9d964e1b ] lost npc in PTRACE_SETREGSET, breaking PTRACE_SETREGS as well Fixes: cf51e129 "sparc32: fix register window handling in genregs32_[gs]et()" Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Valentin Longchamp authored
[ Upstream commit 1a3db27a ] Since the quiesce/activate rework, __netdev_watchdog_up() is directly called in the ucc_geth driver. Unfortunately, this function is not available for modules and thus ucc_geth cannot be built as a module anymore. Fix it by exporting __netdev_watchdog_up(). Since the commit introducing the regression was backported to stable branches, this one should ideally be as well. Fixes: 79dde73c ("net/ethernet/freescale: rework quiesce/activate for ucc_geth") Signed-off-by:
Valentin Longchamp <valentin@longchamp.me> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sasha Levin authored
[ Upstream commit 9fecd132 ] When removing a block group, if we fail to delete the block group's item from the extent tree, we jump to the 'out' label and end up decrementing the block group's reference count once only (by 1), resulting in a counter leak because the block group at that point was already removed from the block group cache rbtree - so we have to decrement the reference count twice, once for the rbtree and once for our lookup at the start of the function. There is a second bug where if removing the free space tree entries (the call to remove_block_group_free_space()) fails we end up jumping to the 'out_put_group' label but end up decrementing the reference count only once, when we should have done it twice, since we have already removed the block group from the block group cache rbtree. This happens because the reference count decrement for the rbtree reference happens after attempting to remove the free space tree entries, which is far away from the place where we remove the block group from the rbtree. To make things less error prone, decrement the reference count for the rbtree immediately after removing the block group from it. This also eleminates the need for two different exit labels on error, renaming 'out_put_label' to just 'out' and removing the old 'out'. Fixes: f6033c5e ("btrfs: fix block group leak when removing fails") CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Nikolay Borisov <nborisov@suse.com> Reviewed-by:
Anand Jain <anand.jain@oracle.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Thierry Reding authored
[ Upstream commit 78ad7342 ] This reverts commit 9f42de8d. It's not safe to use pm_runtime_force_{suspend,resume}(), especially during the noirq phase of suspend. See also the guidance provided in commit 1e2ef05b ("PM: Limit race conditions between runtime PM and system sleep (v2)"). Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit b344579c ] Mirja Kuehlewind reported a bug in Linux TCP CUBIC Hystart, where Hystart HYSTART_DELAY mechanism can exit Slow Start spuriously on an ACK when the minimum rtt of a connection goes down. From inspection it is clear from the existing code that this could happen in an example like the following: o The first 8 RTT samples in a round trip are 150ms, resulting in a curr_rtt of 150ms and a delay_min of 150ms. o The 9th RTT sample is 100ms. The curr_rtt does not change after the first 8 samples, so curr_rtt remains 150ms. But delay_min can be lowered at any time, so delay_min falls to 100ms. The code executes the HYSTART_DELAY comparison between curr_rtt of 150ms and delay_min of 100ms, and the curr_rtt is declared far enough above delay_min to force a (spurious) exit of Slow start. The fix here is simple: allow every RTT sample in a round trip to lower the curr_rtt. Fixes: ae27e98a ("[TCP] CUBIC v2.3") Reported-by:
Mirja Kuehlewind <mirja.kuehlewind@ericsson.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
